hoff70

Forum Replies Created

Viewing 15 posts - 31 through 45 (of 138 total)
  • Author
    Posts
  • in reply to: Long time no see #3661
    hoff70
    Participant

    Looks good! Shame about your hotend 🙁 What failed?

    in reply to: Morgan build Ellaville Ga. US #3625
    hoff70
    Participant

    Well, time to update! I’ve recently overhauled my other printer so it’s back to Morgan!

    Here’s my HE endstop assembly:

    endstop

    Mocked up:

    endstops

    Motors mounted and belts mocked up:

    motors

    The wires are routed through a hole in the bottom plate where they’ll return to the top side on the right. I have a RAMPS bracket on my other printer that I like so I’ll probably use it on Morgan as well.

    That’s it on the right:

    RAMPS

    It’s a nice accessible design that uses an 80mm fan. I’ll probably do a more “steampunkish” grille for Morgan with colors more in keeping with the theme.

    This is the configuration I think I’m going with:

    motors

    Power supply vertical in the back with maybe a glowing amber LED in the case. I think the chrome case showing will be nice.

    in reply to: Building a Morgan in France #3273
    hoff70
    Participant

    Ramps set looks OK although chinese ramps can be a crap shoot. Friend had a transistor soldered into his backwards and it popped! Same goes with Mega clones.

    I don’t want to discourage you but it’s something to consider.

    The BOM calls for DRV8825 drivers on the X and Y so you’ll need to pick some of them up which will add to the total cost.

    Yea, it does look complicated but when it’s done and you’ve sorted it all out it’ll seem easy \o/

    I run an SD card reader/LCD but you don’t need it starting out. It can also make things more complicated because it’s something else to configure in firmware and another possible area to have to troubleshoot… You can always get the machine printing without it and add it in the future once you’re more familiar with things.

    I’d say pick up a RAMPS 1.4 set, a mega and some drivers. Maybe 3 of each type in case one is a dud or you burn one up 😐 Having extras is fun because you can run about any stepper with a Pololu and an Arduino if you like tinkering!

    Pre made wires are also nice. Get a set of wires with female header pins on the end as well. 4 leads for motors and 2 leads for stops. I ended up with 3 leads but just trimmed one wire off for the 2 leads. Pretty cheap and well worth it!

    I’ve used a J-head clone before and it was a dud 🙁 They seem to be a crapshoot as well… I’d say spend the extra for a genuine from hotends.com. It may prevent a lot of frustration in the future. Your printer is only going to be as good as the nozzle.

    I used 3/4″ plywood for my wood parts. I don’t think I’d want to go any thinner than 1/2″ just because of stability.

    Hope this helps a little! And good luck!

    in reply to: Some progress on Morgan build in Tennessee #3237
    hoff70
    Participant

    I cooked the VR on a mega during another build. Can’t remember how I did it…

    I replaced it with a regular 7805 regulator bodged in place of the SMT component. It’s been running like that for a couple of years!

    in reply to: Morgan build Ellaville Ga. US #3157
    hoff70
    Participant

    I ordered these: http://www.ebay.com/itm/221412335628?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649

    plus a Mega. I’m thinking that’ll about be it for parts.

    I have 2 of these for X,Y motors: https://www.sparkfun.com/products/10846

    That plus GT2 belt and 20 tooth pulleys.

    Figured I’d add those links to help folks round up parts.

    Cool that you’ve experimented with the pressure sensors Q. Shame that they don’t seem to be a good option 🙁

    Seems that having the actual hot end “touch off” on the bed would be the best thing but it’s a tricky problem…

    Curious, did you try the sensors under the bed or something else?

    in reply to: Morgan build Ellaville Ga. US #3125
    hoff70
    Participant

    I like the pressure switches under the bed as well! Sure would be neat to incorporate a single sensor into the hotend holder some way…

    in reply to: Morgan build Ellaville Ga. US #3097
    hoff70
    Participant

    The Marlin Delta branch I’m using includes support for a servo driven probe which just seems to complicate things with an extra motor, wiring, code, etc…

    I did a mash-up of other folks work and incorporated it into Rostock:

    Not sure if you’ve seen the setup but it uses magnets, a nail and a HE sensor so It’s not much different from Morgan BOM \o/

    I’m still fooling with Morgan dual-head hardware and was fooling with this:

     photo IMG_1301_zps56116790.jpg

    Looks neat but doesn’t work very reliably 😐

    in reply to: Morgan build Ellaville Ga. US #3089
    hoff70
    Participant

    Yes it is Q! I’ll order the drivers this evening.

    I have a friend who is also building a Morgan and we are about even in our progress as of now so I’m getting re-energized \o/

    Any plans for an auto-level probe setup on Morgan? I was just wondering because I have it set up on my Rostock and I know the Delta/Scara firmwares are similar. I haven’t used it enough to comment on how well it works yet…

    in reply to: Morgan build Ellaville Ga. US #3081
    hoff70
    Participant

    Well, I have been away for a bit tinkering with other things but I am ready to finish this machine \o/

    I received my 400 step motors last week and I believe the only parts left are some drivers and a Mega board.

    From the catching up I’ve done it looks like DRV8825’s are still the recommended drivers? I was just going to run them on all Axis if there wouldn’t be any problems…

    I’ve been messing with GRBL and some stray steppers/drivers so I want some extra drivers around for messing with.

    Thanks in advance!

    in reply to: Morgan build Ellaville Ga. US #1572
    hoff70
    Participant

    Parts availability life interfering or what? Just curious because I’m excited about you getting the farm up and running!

    in reply to: Threadless ball-screw #1571
    hoff70
    Participant

    I’m using the tiny_ballscrew_8mm_38_5 Works fine with Roberts bracket.

    My machine isn’t running yet so it’s all pretty experimental. I’ve drawn up a stiffer bracket that should be easy to print just haven’t printed it yet.

    in reply to: Morgan build Baltimore, MD #1570
    hoff70
    Participant

    Looks sweet \o/ What material did you use for the base and top plate?

    in reply to: Lots of Questions! #1546
    hoff70
    Participant

    You can search through my posts and find some info. I’m in the US as well so I’ve been through the metric/SAE and Z leadscrew stuff.

    Don’t sweat the coach screws just find something that works. I believe I used 3mm.

    Good luck!

    Threadless ballscrew looks promising but not tested yet:

    All good things

    in reply to: Morgan build Ellaville Ga. US #1542
    hoff70
    Participant

    Another project \o/

    So how’s the farm coming Q?

    in reply to: Morgan build Ellaville Ga. US #1540
    hoff70
    Participant

    Perhaps magnets.

Viewing 15 posts - 31 through 45 (of 138 total)
Help-Desk