hoff70

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 138 total)
  • Author
    Posts
  • in reply to: Morgan build Ellaville Ga. US #3981
    hoff70
    Participant

    Just fudged some numbers in config.h and did a dry run:

    in reply to: Building a Morgan in France #3925
    hoff70
    Participant

    Were you going to use a heated bed? I’d recommend going with one now because you’re going to want one eventually!

    in reply to: Morgan build Ellaville Ga. US #3901
    hoff70
    Participant

    Just some random pics:

    Printed a “heatsink” for the top of Z motor and got some retro wire loom:

    stepper

    Belt tensioners installed:

    tensioner

    PSU tower with tubes:

    psu

    Rigged the tubes up to fade RGB:

    It’s a weird sort of insanity I guess \o/

    in reply to: Building a Morgan in France #3897
    hoff70
    Participant

    Check out my build thread about the E3D, I’m about to post some pics. No experience with E3D personally but several experienced people I trust swear that they are the greatest thing ever \o/ These aren’t bowden setups though but from what I understand the E3D doesn’t require much retraction so I have my fingers crossed.

    You can also see my build plate solution on my build thread. I should have my heated plate next week so I’ll post some pics.

    in reply to: Morgan build Ellaville Ga. US #3893
    hoff70
    Participant

    8825 mod shown here: https://www.morgan3dp.com/?s=stepstuck

    Check out the pins on the lower right of the chip in the pic. Two of them have a tiny solder bridge between them :O

    I’ve tested 3 of them on morgan and they work in initial testing but if this is your 1st printer I wouldn’t go too cheap on parts.

    Budget is important (To me at least) but I wouldn’t recommend getting the cheapest parts available. I’ve had a few of the really cheap reprap ebay parts turn out to be duds…

    I’ve had 100% good luck with reprapdiscount and gadgets3d and the prices aren’t that much higher.

    in reply to: Morgan build Ellaville Ga. US #3877
    hoff70
    Participant

    Thought someone may be interested in seeing modified drivers installed:

    drivers

    I used “Wire Wrap” wire from Radio Shack in the US. It’s pretty handy stuff for jumping boards.

    I noticed this on one of the cheap-O drivers I got from ebay:

    bad driver

    Notice the solder bridge between the pins :O That’s just how it came…

    in reply to: Morgan build Ellaville Ga. US #3861
    hoff70
    Participant

    Making progress:

    in reply to: 6805 Bearings #3857
    hoff70
    Participant

    🙁 Maybe a bicycle shop? I know the other bearings are used in skates/skateboards so maybe check some shops?

    Good luck!

    in reply to: 6805 Bearings #3849
    hoff70
    Participant
    in reply to: Morgan build Ellaville Ga. US #3825
    hoff70
    Participant

    DOH!

    e3d

    Looks like I need to go back and shorten the PVC tubes and smooth rods…

    in reply to: Morgan build Ellaville Ga. US #3821
    hoff70
    Participant

    Just got this in the mail:

    E3D

    E3D hotend. I have a friend who swears it’s the greatest hotend ever and he used a J-head previously.

    I’m still a fan of the J-head but we’ll see how this does.

    in reply to: Morgan build Ellaville Ga. US #3805
    hoff70
    Participant

    I actually went to a lot of silly trouble to do just that Q :O After much fiddling to get the actual heaters working I was rewarded with a rather dim glow that was barely noticeable 🙁

    Now nixies would be AWESOME!

    in reply to: Morgan build Ellaville Ga. US #3793
    hoff70
    Participant

    Stuck some RGB LED’s in the tubes to be extra goofy!

    in reply to: Morgan build Ellaville Ga. US #3789
    hoff70
    Participant

    Still tinkering around a bit:

    PSU

    I figured mounting the PS vertical would be cool but it needed some decoration on top!

    in reply to: Long time no see #3781
    hoff70
    Participant

    Looking forward to hearing your opinion of the Pico!

Viewing 15 posts - 16 through 30 (of 138 total)
Help-Desk