hoff70

Forum Replies Created

Viewing 15 posts - 121 through 135 (of 138 total)
  • Author
    Posts
  • in reply to: Threadless ball-screw #1000
    hoff70
    Participant

    I say go for the air bearings! Sounds like it would over complicate things a bit but what the hey! You may be on to something. Plus experimentation is always fun 🙂

    I believe the Morgan would be a good candidate for simple printed linear bearings. My guess is that since Z is the only axis on linears the relatively small motions (compared to X and Y slides on other variants) may allow them to hold up for a good long while. The length of the Morgan slides should also help spread the load and reduce wear. It would also knock 4 “store bought” components off the BOM!

    More mock-up:

    z motion

    Another view:

    z motion

    Someone should run with this printed nut and make more of it printable :O It may not be possible with roller bearings but printed rollers on screws may work… The galling that the bearings are making on the soft rod puts me in the mind of a fixture for making a lead screw out of smooth rod. Once “threaded” the rollers could be replaced with plastic rollers.

    in reply to: Threadless ball-screw #977
    hoff70
    Participant

    I like it as well! I also think it’s neat because it’s possible to print roller bearings. Not that we could print very usable bearings now, but maybe in the future…

    I also like the fact that they are pretty common and inexpensive items.

    My only worry is that it adds 7 more bolts that can come loose. I have a rostock so I’m an expert at loose nuts \o/

    in reply to: Threadless ball-screw #974
    hoff70
    Participant

    Yes, I’ve noticed some galling already with the rods I’m testing with. They are supposed to be drill rod but are really soft. I could just have the bearings adjusted too tightly but some pretty hard rod would be a good idea.

    in reply to: Threadless ball-screw #971
    hoff70
    Participant

    Here’s the beta version:

    bracket

    They are balloons instead of teardrops 😛

    I printed the 38.5 deg version because I figured it needed a pretty fast thread. The orientation of the bolts seem OK to me Robert. I like the way it tucks into the bracket instead of sticking out. Probably be best to remove the 3 bolts holding the assy. to the bracket and removing it for maintenance…

    And good job Robert! I was thinking about just adding a pad to the bottom of the original bracket but that would have made access to the mounting screws difficult. Your solution makes for easy access 🙂

    I gotta say it’s pretty darn “grippy”. As long as the bolts stay tight I reckon it’s a pretty good solution.

    in reply to: Threadless ball-screw #964
    hoff70
    Participant

    I think it’s going to work fine but it could probably use some stiffening up:

    bracket

    in reply to: Threadless ball-screw #963
    hoff70
    Participant

    Robert was gracious enough to put this together Q!

    I think I would have preferred the bracket to be all the way at the bottom so it could print flat on the bed as you say as well as have the points on the drops at the top. But those are minor niggles and we appreciate your work Robert!

    I hope to have the print finished soon and will begin on the “ball screw” I believe I may actually have the bearings and hardware on hand which will be nice.

    I’ll post some side by side pics of both parts when this one is out of the oven.

    in reply to: Threadless ball-screw #959
    hoff70
    Participant

    I noticed the part where the “Z arms” mount is a lot thicker:

    z bracket

    Morgan sure has some beefy parts compared to most other repraps!

    in reply to: Threadless ball-screw #953
    hoff70
    Participant

    Thanks! I’m printing the bracket now. Rostock has been temperamental lately so hopefully it will go well.

    in reply to: Threadless ball-screw #942
    hoff70
    Participant

    Great!

    Please post a link to the file. I printed your tool holder for the German bowden setup and it turned out pretty well.

    Thanks for the work you are doing!

    in reply to: Reprap Morgan Building From Asia!But I need a help! #939
    hoff70
    Participant

    Sorry I can’t help much but I just wanted to say nice work!

    Perhaps you need to change the default feedrates in your firmware? I believe that jogging the motors “looks” to these parameters in firmware for speed and perhaps going up on these values will help.

    in reply to: Morgan build Ellaville Ga. US #891
    hoff70
    Participant

    Well, the parts bin is growing!

    parts

    Still waiting on some mail order parts.

    in reply to: DXF File #859
    hoff70
    Participant

    Thanks for the work on the template! I just printed mine out.

    I’m not entirely sure but I’d imagine the thickness isn’t that important because the critical dimensions will be from the top of the bottom plate to the bottom of the top plate. I believe that the inside measurement is what is most important and the thickness shouldn’t effect it.

    I think I’m going to go with some 3/4″ jointed pine from Lowes.

    in reply to: Morgan build Ellaville Ga. US #857
    hoff70
    Participant

    A little progress:

    parts

    As you can see I’m mostly printing/gathering parts. I have the build platform almost together and have assembled the tube/wheel/arm portion. I’m awaiting some bearings via mail and then I need to round up the bolts and washers.

    I have been studying the 9 degree steppers and what drivers will be required. The small stepper in the picture is for the extruder I plan on using. It’s very small and light and I was thinking about mounting it on the head instead of using the bowden arrangement. Not sure if it would work out or not… Just an idea.

    I also made a board for Gen 7 electronics. I’m not sure if it will be any cheaper than mega/ramps but I’ve been wanting to do it so we’ll see how it goes!

    in reply to: DXF File #847
    hoff70
    Participant

    Neat! So the cutout from the bottom piece is used for the top piece? I haven’t gotten that far yet.

    in reply to: SAE equivalent parts / adapters #844
    hoff70
    Participant
Viewing 15 posts - 121 through 135 (of 138 total)
Help-Desk