mk3v

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 26 total)
  • Author
    Posts
  • in reply to: Full Graphic LCD question #5719
    mk3v
    Participant

    Hi,

    I’m also very interested in using that kind of LCD…
    Did you manage to get one working ?

    I tried to merge your FW with another one which supports GLCD, but I never could achieve it.

    K.

    in reply to: Perpendicularity calibration #5689
    mk3v
    Participant

    Hi !!

    I changed my motor mounts with the new ones and tightened the belts a bit more.
    And I finally re-calibrated my M92 and M365.
    So I think it was just that…problem solved.

    in reply to: French makers here ! #4109
    mk3v
    Participant

    Hello there,

    I just wanted to point out a strange thing :

    I needed to print a set of herringbone gears for the 3mm extruder.
    But with le latest STL’s the small gear is inverted, so I checked the instructions on the last reprap magazine and it’s not working the way it’s shown.

    I think the small gear has been modified, because in the kit I bought to build my morgan, the small gear is fine…

    Could it be possible to get the old one back ?

    in reply to: French makers here ! #3749
    mk3v
    Participant

    I was using the default grid 5×5.
    Maybe I will try 7×7 or 8×8.
    It will be long, but maybe it’s worth it…

    in reply to: French makers here ! #3741
    mk3v
    Participant

    OK, I will try to increase the numbers of rows and columns.
    But do you really think it can correct my default of curved shape ?

    Or do I have another mechanical problem…?

    in reply to: French makers here ! #3713
    mk3v
    Participant

    Hi,

    I still have some problems with large parts.

    I was wondering how the level auto-correction works.
    Since it seems that my nozzle doesn’t move on a flat plan but on a curved shape.
    If I move the nozzle on the same X line : at Y0, I could be 0.5 mm far from the bed ; at Y100, I’m just touching the bed ; and at Y200, the nozzle is again 0.5 / 1 mm far from the bed.
    And I don’t think my glass bed isn’t flat, I tested it on a marble bench at work…

    So does the auto-correction works with this kind of default ??

    in reply to: French makers here ! #3449
    mk3v
    Participant

    I’ve got 400 mm/s2 for X,Y and Z.
    Maybe I should reduce acceleration on every axes due to my hardware (400 steps motors and 1/32 ustepping) ?

    in reply to: Building a Morgan in France #3445
    mk3v
    Participant

    Salut les gars !!

    Actually, you can find stainless threaded rods in shops like Leroy Merlin for a few € per meter.

    But I think I will try the drill bit or this kind of lead screw :

    http://openbuildspartstore.com/8mm-metric-lead-screw-acme/

    The standard M8 nuts can’t run as lead screw nuts for a very long time. The first I used died quickly, and I hope it was just because it was a bad one.

    Good luck…

    K

    in reply to: French makers here ! #3429
    mk3v
    Participant

    OK, I never tried to tweak the acceleration value.
    I think my speed value is around 2.

    I will try to modify the acceleration values this evening and I will let you know what I find.

    Quentin, could you tell me which value to start with for the acceleration ?

    in reply to: French makers here ! #3421
    mk3v
    Participant

    Hi !

    I think you’re using a threaded rod just like me.

    So you have to change the max speed of the Z motor.
    Just experiement with pronterface… I’m using 60 mm/min for joggning Z axis in pronterface.
    It gives 1mm/sec to load in the firmware with M203, but the hardware can go a bit faster, I will tell you later which value I put in the firmware.

    K

    in reply to: Building a Morgan in France #3289
    mk3v
    Participant

    Hi !!

    I think the kit on DX is OK but you’ll need 1/32 ustepping drivers.
    I bought them on reprapworld.com, I chose the stepsticks and I use one of them for each motor.

    Otherwise the funduino is OK the red ramps and the LCD also.

    But be carefull with their J-Head, you should also take one from reprapworld.

    And for the motors, search for wantai motors on eBay, they can be shipped from germany and they have good 400 steps motors.

    Good luck !!
    K

    in reply to: French makers here ! #2917
    mk3v
    Participant

    OK so I can put the setting I found on pronterface for jogging Z axis correctly…?

    I am at 20 mm/min when doing the bed auto correction and it seems to be fine.

    in reply to: French makers here ! #2901
    mk3v
    Participant

    I have 400steps motors and 1/32 usteps.
    My M92 value for Z is 10244.79 calibrated with yours method…

    EDIT : and a M8 screw

    in reply to: French makers here ! #2889
    mk3v
    Participant

    Hey nice work Flo !

    I was wondering if it’s possible to decrease the speed of the M371 move, and also for M372.
    I think the speed for my hardware is too high…

    Quentin, is there a way to do that ?

    K

    in reply to: French makers here ! #2813
    mk3v
    Participant

    Here’s what I was talking about :

    http://hpics.li/757202b

Viewing 15 posts - 1 through 15 (of 26 total)
Help-Desk