Forum Replies Created
-
AuthorPosts
-
mk3v
ParticipantAtually, instead of florent I have a 1.75 mm filament for a 0.35 nozzle.
The problem is I don’t really have to clean the nozzle but I need to get back all the filament out the PTFE tube and there is always about 5mm of molten PLA at the end of the PTFE tube (I will try to take a picture).
Then I increase the hotend temp to 170 / 180, I put the tube with the “blocking” PLA in the hotend a few seconds.
At this time I can push the “blocking” PLA with fresh filament.
But at the next long print the problem comes again.
mk3v
ParticipantSalut Florent,
I think I have the same problem…
I tried to print the new motor mounts, the short one went correctly, but the print of the tall one failed at half-height.
I think it’s due to the fact that I maybe have a bad J-head and the heat goes up in the PEEK part and the PLA get melted over time during the print and when enough length of PLA is melted is sticks very hard to the PTFE tube.So I think we have to cool down the PEEK part of the J-head during print or Quentin will have teach us another trick to get through that problem…
A+
K
mk3v
ParticipantHello,
I’ve solved a lot of little problems I had.
And now I’m pretty satisfied of my first print tests.But there is still one thing that appears on prints like the calibration part, it’s a gap between the perimeters and the fill-in, but just on the right side of X:
It’s weird and I don’t know where it’s coming from.
I will try to print it not on the center of the bed, just to see what happens.But if someone knows what it could be ??
Just let me know 😉
K
mk3v
ParticipantHi guys !!
I think I finally solved my problems and finished the calibrations.
I used the ini files in morgan master to configurate slicer.
But my first print is a mess, there is a lot of parameters in slicer and I don’t really know wich one to start with.Here’s a pic of this print :
Hope you can guide me a bit with this…
Cheers,
K
mk3v
ParticipantOh I was mistaking when calcuting, I had to divide by 1.25 instead of multiplying.
So I’m OK with something around 10200…
mk3v
ParticipantFirst I caclulated 400 x 32 x 1.25 –> 16000 steps/mm
Then with the first step of the Z calibration I had about 10200 steps/mm.
mk3v
ParticipantWell, I followed exactly what you explained…
The z offset I had was very absurd but I did it, just to be sure.
And at M371 the bed encountered the nozzle.
I think my problem is more mechanic.
I use a M8 threaded rod as Z-screw with two nuts, one at the bottom and one I inserted in the hexa hole a bit tighten against a spring.
How much does is have to be tighten in this configuration ?
During the trip from Z-home to Z10 the motor speed changes several times and sometimes it goes down a bit while it was going up, then it goes up again…
Could it be a motor or a driver problem ?
And the sound the motor makes while jogging with pronterface is completely different from the sound while travelling in G1. Is it normal ?
Or is it simply my chinese deal extreme RAMPS ?!?
This is enough questions for now…
mk3v
ParticipantHi,
It’s pretty simple, you’ll juste have to configure the firmware due to the hardware you chose :
https://github.com/qharley/Marlin/tree/armlevel
You’ll have to load the firmware with the Arduino software available on the official arduino website.
Then you’ll be able to connect your electronics to your PC with these softs :
http://koti.kapsi.fi/~kliment/printrun/
Actually, I think pronterface is the only easy way to do the calibration…
And the others softs are to make the G-codes (slicer, and you can also download Cura…).
At the beginning I was not sure about all the wiring an d I found this belgium wiki for another printer which is good if you wish to use a RAMPS board :
http://mchobby.be/wiki/index.php?title=3D-OrdBot-Ramps
with this for testing purpose :
http://3dnotepad.blogspot.fr/2013/10/test-des-ramps.html
Have fun !!
mk3v
ParticipantYep !!
For the steppers drivers, I don’t think it’s about high or low current, it’s about more or less microstepping.
I chose to buy the stepstick DRV8825 available on nreprapworld.com.
They are a bit cheaper than pololus and they do the job pretty well…Then you can chose if you want your driver to run 1/16 or 1/32 substeps, with a 400 steps motor you can have 12800 microsteps.
If you chose to buy only 400 steps motors and drivers that can go to 32 substeps you will just have to configure the firmware with the good steps per mm…
I hope this is not too confused…
mk3v
ParticipantHi guys !!
My build is finished…
I think calibration is OK.
But when I try to print the SCAL part with the settings found in Morgan Master, the bed goes up but it doesn’t stop at zero but it tries to go further up…
I think it’s a param in Slicer… but wich one ?
FYI I tried to print from an SD card and the smart LCD thing…
Thanks for your help.
Kevin
mk3v
ParticipantHi,
And welcome !!
I’m also a french builder.
I bought exactly the same motors, no problems so far.
It’s a chinese reseller and they have a German warehouse, so be careful to buy some from this warehouse.For the printed parts I asked JP who is another french builder, you will find him in the french builders topic.
For the electronics : RAMPS, Funduino, smart LCD and others, I purchased it from dealextreme.com.
It’s not very fast but it’s cheap and quality is OK.For the special electronics, filament, bearing, stepsticks, and special stuff, I went directly to reprapworld.com
They are in Netherlands, so it’s quite fast to France and not so expensive.I wish you good luck !!
Kevin
-
AuthorPosts

