Help : reprap morgan instructions in reprap magazine issue 3 now

All good things › Forums › Morgan Builders forum › Help : reprap morgan instructions in reprap magazine issue 3 now

Viewing 5 reply threads
  • Author
    Posts
    • #2657
      monamour
      Participant

      this morning I’m sawing reprap magazine have published
      i am very happy so i will start build my reprap morgan
      i see all instructions but i don’t found any instructions for software and electronics connections and tell me how to install firmware may any one help me ??
      ======================
      and my important questions can i connect SD card and LCD screen and manage my 3dprinter and print without connect with computer ??
      =========
      I’m waiting this is the link for reprap magazine to help any one need to build his own morgan 3d printer
      http://reprapmagazine.com/

    • #2661
      Quentin Harley
      Keymaster

      Hi monamour,

      It a previous issue of the reprapmagazine there is a comprehensive qrticle on the different RepRap electronics available.

      I do not cover the electronics here, because I do not know what you are going to use.

      My advice would be to get electronics that is Marlin compatible, and look in its web site or wiki (reprapwiki is a good place to start) for the wiring diagrams and instructions.

      For me to document every possible set of electronics used on Morgan would be a waste of time, and can be spent in much better ways.

      I quite like RAMPS 1.4, and it may be the easiest to get going using it, since you need no special tricks to get the Arduino software to send the firmware to the Arduino Mega. It also has a couple of LCD shield options available, with SD card , most notably the Reprap discount one.

      Ramps also has the best documentation I have seen so far on the reprapwiki…

      Hope it helps.

    • #2665
      monamour
      Participant

      i think the best choose for me ramps 1.4 ,SD card and LCD
      i can print with this without my computer this is your meaning ??
      but may you tell me how to set up my software and
      Firmware please tell about the software which using in the 3dprinter i don’t know any thing 🙁 and design things to print how , I know I disturbed you a lot but I’m a beginner I’m sorry

    • #2669
      Quentin Harley
      Keymaster

      It is too much info for a single post…

      Lets try:
      1) install arduino from the arduino.org website
      2) install Slic3r from its website
      3) install pronterface – search for a copy for your operating system
      4) download the Morgan firmware and the Morgan hardware zips from my git repositories. The links are in a sticky on the homepage of this blog
      5) follow the Marlin installation instruction to get the firmware on the Arduino Mega.
      6) install the board according to the reprap wiki instructions. If you are not sure what to do, find a person with some electronic skills to help you.
      7) follow the startup guide page on this blog.

      Find fellow reprappers. There must be at least a couple close to where you are. The best way to learn it to try, and have some real person to show you.

      Google is your friend. I taught myself almost everything I know, and you can too.

      Read the blog, and the other forum topic posts. A lot of your questions have been asked and answered before.

      Good luck!
      Q

    • #2693
      Quentin Harley
      Keymaster

      Hi,

      With LCD and SD card the machine runs with no PC attached.

      Info here: http://reprap.org/wiki/RAMPS_1.4

      Ramps connections

    • #2697
      Quentin Harley
      Keymaster

      Info on the LCD SD controller here:

      http://reprap.org/wiki/RepRapDiscount_Smart_Controller

      You will notice it is all on the reprap.org wiki.

      Search and you shall find

    • #2685
      monamour
      Participant

      but my important question can i run and manage my 3d printer with out my computer and print from SD card ?? and screen??
      and can i choose the file i want to print from SD card and screen ??

      and do you have any instruction ?? for electronics and software like the instructions in reprap magazine ?
      ===========
      I hope that is not sad from me
      ===========

      thank you

Viewing 5 reply threads
  • You must be logged in to reply to this topic.
Help-Desk